Release notes for WP-UMX-TPS-TX100

v1.4.0b8

Release date: 2019-07-23

New feature:

• Added support for FP-UMX-TPS-TX120-GES, FP-UMX-TPS-TX130-GES product variants.
• New bootloader is used, which allows the connected TPS-RX95's to be upgraded remotely.
• EDID node properties changed: PreferredResolution, MonitorName and AudioInfo properties are added
• Event Manager upgraded: time delay can be configured between condition and action, a condition can trigger multiple actions at the same time, inverse condition can be used.
• IR command injection is now supported: data received on a specific TCP port is transmitted as IR signal, and the received IR frames are also sent to this TCP connection.
• New EDID driver is used, the content of some factory EDID's are changed according to EDID 1.3 and 1.4 standard.
• Autoselection connect and disconnect delay can be configured via LW3 methods.
• The device is able to identify IR commands on either the local or link IR input port. This feature can be connected to Event Manager, which means, that the device can be programmed to do various actions, if a specific IR command is detected.
• Crosspoint properties and methods changed. Warning: If you are using an external controller for this device via LW3 protocol, the recent changes in property and node names may result in difficulties to control the TPS device with the latest firmware.
• TCP and UDP messages can be sent by the device to control projectors and any other devices. This feature can also be used with Event Manager.
• WP-UMX-TPS-TX100-WHITE products are now supported.
• The method of storing device settings in EEPROM is upgraded, which may result in losing all the settings, logs and user EDID's after upgrading to 1.1.0. The LDU software contains a plug-in to help you keep the actual settings after firmware upgrade.
• Audio and video port names are changed: 'I' is used for inputs and 'O' is used for outputs, instead of 'P'.
• 3840x2160p60 YUV4:2:0 factory EDID added.
• Event Manager configuration became more user friendly: actions can be triggered manually for testing and the user interface shows if any of the conditions are met.
• Fan can be controlled manually with setFan() LW3 method.
• Sending IR codes (SendProntoHex e.g. send max. 200 Byte IR code with Event Actions) for UMX-TPS-TX140-Plus only!
• LWROS integration compatible for LDU2 only!
• Modified DP input driver to fix HDCP issue with MacBooks
• Modified RS-232 modes to support SendMessage in Control mode
• CEC - sendCEC command (e.g. turn on the TV with Event Actions) for WP-UMX-TPS-TX130-Plus only!
• Added 'User replaceable miniweb slot' to support built-in control webpage
• Added 'Dark mode' function to turn off front panel LEDs
• Improved GPIO detection
• RS232 Minimal Recognizer for Cisco compatibility (Cisco Login) for WP-UMX-TPS-TX130-Plus only!
• Firmware platform library updated
• Use LDU2 v1.2.5 or later for the upgrade!
• Added 'Disable default button function' option to support button customization in Event Manager
• Added 'Forced button lock' function to lock buttons via protocol command

Bugfix:

• In case of sending 1920x1200 no sync screen, the device did not notice the connection state changes on the inputs. Fixed.
• Compatibility issues with Gefen HDMI 1.3 HdBaseT extender fixed.
• In case of sending DVI signal on the output, the audio output port does not indicate signal present.
• Input video parameter measurement speed improved.
• If no sync screen is active, the output resolution is now reported correctly by the output port.
• /SYS/MB/UMXDP node renamed to /SYS/MB/DP
• Reporting the resolution of signals in YUV 4:2:0 colorspace fixed.
• Event manager conditions did not work if DP input properties were selected.
• If the user switched to the currently selected port, the output was disconnected and connected again unnecessarily, which resulted in a picture drop. Fixed.
• Poe enable state is now reloaded after reboot.
• If the output was set to HDCP Always mode, the signal was sent out unencrypted, if the input port was disconnected and connected again. This issue only happened, if the input signal was also unencrypted.
• Unsupported dual link DVI EDIDs removed from factory EDID list.

v1.3.1b1

Release date: 2019-05-21

New feature:

• Added support for FP-UMX-TPS-TX120-GES, FP-UMX-TPS-TX130-GES product variants.

v1.3.0b1

Release date: 2019-04-17

New feature:

• FP-UMX-TPS-TX100-MK products are now supported.

v1.2.0b1

Release date: 2019-05-21

New feature:

• WP-UMX-TPS-TX100-WHITE products are now supported.

v1.1.1b1

Release date: 2019-05-21

New feature:

• Autoselection connect and disconnect delay can be configured via LW3 methods.

Bugfix:

• Input video parameter measurement speed improved.
• /SYS/MB/UMXDP node renamed to /SYS/MB/DP
• Event manager conditions did not work if DP input properties were selected.
• If the user switched to the currently selected port, the output was disconnected and connected again unnecessarily, which resulted in a picture drop. Fixed.
• Unsupported dual link DVI EDIDs removed from factory EDID list.

v1.1.0b4

Release date: 2019-05-21

New feature:

• The method of storing device settings in EEPROM is upgraded, which may result in losing all the settings, logs and user EDID's after upgrading to 1.1.0. The LDU software contains a plug-in to help you keep the actual settings after firmware upgrade.
• New bootloader is used, which allows the connected TPS-RX95's to be upgraded remotely.
• Audio and video port names are changed: 'I' is used for inputs and 'O' is used for outputs, instead of 'P'.
• The device is able to identify IR commands on either the local or link IR input port. This feature can be connected to Event Manager, which means, that the device can be programmed to do various actions, if a specific IR command is detected.
• IR command injection is now supported: data received on a specific TCP port is transmitted as IR signal, and the received IR frames are also sent to this TCP connection.
• EDID node properties changed: PreferredResolution, MonitorName and AudioInfo properties are added
• 3840x2160p60 YUV4:2:0 factory EDID added.
• Crosspoint properties and methods changed. Warning: If you are using an external controller for this device via LW3 protocol, the recent changes in property and node names may result in difficulties to control the TPS device with the latest firmware.
• Event Manager configuration became more user friendly: actions can be triggered manually for testing and the user interface shows if any of the conditions are met.
• New EDID driver is used, the content of some factory EDID's are changed according to EDID 1.3 and 1.4 standard.
• TCP and UDP messages can be sent by the device to control projectors and any other devices. This feature can also be used with Event Manager.
• Fan can be controlled manually with setFan() LW3 method.
• Event Manager upgraded: time delay can be configured between condition and action, a condition can trigger multiple actions at the same time, inverse condition can be used.

Bugfix:

• In case of sending 1920x1200 no sync screen, the device did not notice the connection state changes on the inputs. Fixed.
• Compatibility issues with Gefen HDMI 1.3 HdBaseT extender fixed.
• In case of sending DVI signal on the output, the audio output port does not indicate signal present.
• If no sync screen is active, the output resolution is now reported correctly by the output port.
• Reporting the resolution of signals in YUV 4:2:0 colorspace fixed.
• Poe enable state is now reloaded after reboot.
• If the output was set to HDCP Always mode, the signal was sent out unencrypted, if the input port was disconnected and connected again. This issue only happened, if the input signal was also unencrypted.